ZAVORÉ
ZAVORÉ
✦
Where Artistry Begins
Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·Tracked delivery across the UK and worldwide·Same day and 24 hour delivery available·Venetian plaster tinted to your exact colour·Damaged in transit? We’ll replace it within 24 hours or on the same day·Speak to a specialist · 07592 929191·Residential and commercial projects installed by our own team·Trade accounts · 10% and rewards·Training courses at our studio·Showroom · visit by appointment·
Home/The Journal/Microcement vs Polished Concrete, Thickness, Weight and Cost
26 September 2026

Microcement vs Polished Concrete, Thickness, Weight and Cost

A grey concrete effect surface with a subtle mottled texture, microcement compared with polished concrete

The short answer: polished concrete is a concrete slab that has been ground and honed until it shines, while microcement is a thin cement based coating laid over something that already exists. One is the structure. The other is a finish applied to it. That single difference decides almost everything else. What you can put it on, how much weight it adds, whether it works on a wall, and what it costs to get.

If you want it installed, our own applicators handle microcement installation from survey to final coat.

If you are choosing between microcement and polished concrete for a house or a shop fit out, the honest starting point is usually which one your building can actually take.

Microcement vs polished concrete: the real differences

Microcement Polished concrete
What it is Cement, polymers and fine aggregate, applied as a coating A cast concrete slab, mechanically ground and polished
Thickness Millimetres, not centimetres The full depth of the slab
Added weight Very little The slab is the weight
Substrate Screed, concrete, tiles, plasterboard, timber based boards, all prepared and primed Needs a slab, poured and cured for the purpose
Walls Yes, walls, floors, stairs, sills and joinery Realistically floors only
Look Mineral and cloudy, colour tinted through the material Ground aggregate exposed, colour from the mix and the stones in it
Joints Seamless over large areas, with movement joints respected Saw cut joints and bay layout are visible
Installed in An occupied, finished building The build programme, before fit out

Weight and thickness decide most projects

Polished concrete is not a layer you add. It is the slab you already poured, refined. To get it you need a slab of the right mix, laid flat, cured, then ground back through progressively finer diamonds and densified. That works beautifully in a new build or a ground floor extension where the slab was designed to be the finished floor.

It does not work on a first floor of a Victorian terrace. You cannot add a concrete slab to a suspended timber floor without engineering it, and most of the time the answer from a structural engineer is no. This is why so many “polished concrete” upstairs floors and mezzanines are, in fact, microcement. Microcement adds a coating measured in millimetres over the deck that is already there, which is the whole reason it exists.

The same logic applies upwards. Searches for polished concrete walls are really searches for a concrete look on a wall, because nobody is casting and grinding a vertical slab in a domestic room. That look comes from either microcement or a concrete effect plaster, and we would usually point you at the concrete effect finish for walls where you want board marks, pour lines and shuttering detail rather than a smooth floor surface. Our article on concrete effect walls covers that in detail.

How they look, side by side

Polished concrete looks like what it is: a stone floor made in place. Grinding cuts through the surface paste and exposes the sand and aggregate in the mix, so you see a speckle of cut stone. The depth of that exposure is a choice, a light grind shows almost none, a deep grind shows a terrazzo like scatter of stones. Bay joints and saw cuts are part of the design.

Microcement looks like a soft, cloudy mineral surface. There is no aggregate to expose, so the character comes from the trowel: subtle tonal movement, slightly darker and lighter passes, the odd trowel mark left deliberately. It is quieter and more even than polished concrete, and because it is tinted in the tub, the colour range is far wider than a concrete mix will give you. If you want a warm grey, a putty or a near black floor, microcement will get you there; a slab will not.

One thing to accept about both: they are handmade mineral surfaces and they will not be uniform. That variation is the point. If you want dead flat consistency, you want a manufactured sheet product instead.

Substrate preparation is where the work is

For microcement, the substrate has to be sound, clean, rigid and primed with the right primer for what it is. A deflecting floor is the one thing a thin coating cannot survive, so timber decks get stiffened and screwed down, and movement joints in a screed are carried through the finish rather than covered over. Tiles can stay if they are well bonded, which is often the fastest route in a refurbishment. See microcement floors in the UK for how we approach floor build ups.

For polished concrete, the preparation happened months earlier, in the specification of the slab. Mix design, flatness tolerance, crack control and curing all get decided before anyone thinks about the finish. You can grind and polish an existing industrial slab, and that can be a good outcome in a warehouse conversion, but you take the slab you are given: old repairs, service trenches and patches will all show.

Cost, disruption and programme

We will not quote you square metre rates in an article, because they depend on the state of the substrate, the access and the size of the job, and a made up number helps nobody. What we can tell you is where the money goes.

Polished concrete concentrates its cost in the slab and the grinding: heavy plant, dust extraction, several passes and a densifier. It is efficient over a large open area and awkward and expensive over a small, cut up one, because the machines cannot reach the edges.

Microcement concentrates its cost in labour and preparation. Every coat is applied by hand, so a complicated room with lots of edges, steps and reveals takes proportionally longer. Materials are a modest share of the total, beton stucco is £145 for 16kg, primer is £10 and sealer is £25, and the applicator time is the real number. Our guide to microcement cost in the UK sets out what drives it.

On disruption, microcement wins comfortably in an occupied building. There is no breaking out, no skip, no wet slab curing for weeks, and walls and floors can be finished in the same material on the same visit.

Questions we get asked

Can you put polished concrete on a wall?

Not in any normal building. Polished concrete is a slab ground and honed in place, and you cannot cast and grind a vertical slab in a finished room. For a concrete look on a wall you want microcement or a concrete effect plaster, both applied as coatings. They give you the same visual language with none of the structural demands.

Is microcement as hard wearing as polished concrete?

A polished concrete slab is the tougher surface in absolute terms. It is many centimetres of concrete. A sealed microcement floor is perfectly capable in homes, shops, cafes and offices, and its performance depends far more on the substrate beneath it and the sealer on top than on the coating itself. On a firm base, properly sealed and cleaned sensibly, it lasts.

Can microcement be laid over an existing concrete floor?

Yes, and that is one of its best uses. A sound concrete or screed floor is an ideal substrate once it has been cleaned, mechanically prepared and primed. Existing cracks and movement joints have to be dealt with honestly rather than coated over, because a thin finish will always telegraph movement underneath it.

Which is easier to repair?

Microcement, in most cases. A damaged area can be prepared, recoated and blended, and because the colour is tinted to a recorded reference we can match it again later. Polished concrete repairs are grinding and patching jobs, and a patch in a ground slab rarely disappears completely because the exposed aggregate cannot be recreated.

Where to go next: if the building can take a slab and the floor is on the ground, polished concrete is a fine choice and you want a concrete specialist. If you are working with what is already there, or you want the look on walls as well as floors, start on the microcement page, browse tinted materials in the shop, and call us on 07592 929191 if you would like us to look at the substrate first.

Back to the Journal

Providing luxury finishes for the most prestigious addresses in the world

Venetian plaster, limewash, microcement, tadelakt, metallics, sculptural plaster and gold leaf, supplied and installed by our own team, with Venetian plaster taught at our Birmingham studio.

PayPal
© 2026 Zavoré Ltd · Est. 2021 · Made to order in Birmingham
For The Trade Three ways to earn with us
Trade accountTen percent off every material in the shop, and a specialist on the phone. Partners & affiliatesGet listed where customers find you, or sell our materials and earn on every order. The Rewards RoomEvery order earns. Samples, tools and an apron, on the house.
Free to join · we reply within 24 hours
IT